Sunday, November 3, 2019

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1956

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1956

锟斤拷If any DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic

Trouble Code (DTC) List - Vehicle).

* Allow the engine to reach operating temperature. With the engine running, observe the HO2S parameter with a scan tool. The HO2S value

should vary from approximately 40 mV to approximately 900 mV, and respond to fueling changes.

锟斤拷If the value does not vary from approximately 40 mV to approximately 900 mV, refer to DTC P0131, P0132, P0137, P0138, P0151,

P0152, P0157, or P0158 (See: P Code Charts/P0131), DTC P0133, P013A-P013F, P014A, P014B, P0153, P1133, or P1153 ( See: P

Code Charts/P0133) or DTC P0134, P0140, P0154, or P0160 (See: P Code Charts/P0134).

Note: EVAP purge enablement may cause the FT to be momentarily outside the normal range.

* The normal Short Term FT parameter should be between +10 % and -10 %, with near 0 % the optimum, with the engine running at operating

temperature.

* The Long Term FT parameter should be between +10 % and -10 %, with near 0 % the optimum, with the engine running at operating

temperature.

* Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

P0171 or P0174

Allow the engine to reach operating temperature. With the engine running, observe the affected Long Term FT parameter with a scan tool. The

reading should be between 0-19 %.

If not within the specified range, inspect for the following:

* With the ignition ON and the engine OFF, observe the manifold absolute pressure (MAP) sensor parameter. The MAP sensor pressure should

be within the range specified for your altitude. Refer to Altitude Versus Barometric Pressure (See: Powertrain Management/Computers and

Control Systems/Specifications/Altitude Versus Barometric Pressure).

锟斤拷Refer to DTC P0106 (See: P Code Charts/P0106) if the MAP sensor does not indicate the correct barometric pressure.

* With the engine idling, observe the mass air flow (MAF) sensor parameter. The MAF sensor parameter should be within 2-6 g/s at idle.

锟斤拷Refer to DTC P0101 or P1101 (See: P Code Charts/P0101) or DTC P0102 or P0103 (See: P Code Charts/P0102) if the MAF sensor

parameter is not within 2-6 g/s at idle.

* Vacuum hoses for splits, kinks, and improper connections

* Insufficient fuel in the tank

* Low fuel pressure-Refer to Fuel System Diagnosis (w/o FPCM) (See: Powertrain Management/Computers and Control Systems/Testing and

Inspection/Component Tests and General Diagnostics)Fuel System Diagnosis (FPCM) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics).

* Fuel contamination-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool) (See: Powertrain Management/Computers

and Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without

Special Tool))Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool)) for Gasoline or Fuel Composition Diagnosis

(See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General Diagnostics) for E85.

* Malfunctioning fuel injectors-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and Exhaust/Exhaust System/Testing and

Inspection/Symptoms - Engine Exhaust).

* Missing, loose, or leaking exhaust components from the HO2S forward-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and

Exhaust/Exhaust System/Testing and Inspection/Symptoms - Engine Exhaust).

* Vacuum leaks at the intake manifold, the throttle body, and the injector O-rings

* The air induction system and the air intake ducts for leaks or for a missing air filter element

* A cracked EVAP canister

* Evaporative pipes obstructed or leaking

* The crankcase ventilation system for leaks

* The HO2S for improper installation and for electrical wires or connectors that may have contacted the exhaust system

* The HO2S signal circuit open, shorted to ground, or shorted to the low reference circuit

* Malfunctioning engine components-Refer to Symptoms - Engine Mechanical (See: Engine, Cooling and Exhaust/Engine/Testing and

Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine Mechanical).

P0172 or P0175

Allow the engine to reach operating temperature. With the engine running, observe the affected Long Term FT parameter with a scan tool. The

reading should be between -19 and 0 %.

If not within the specified range, inspect for the following:

No comments:

Post a Comment