Sunday, November 10, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 2729

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 2729

4. Verify that a test lamp does not illuminate between the ignition circuit terminal E and the appropriate cylinder deactivation solenoid control

circuit terminal listed below.

* Cylinder deactivation solenoid valve 1 terminal C

* Cylinder deactivation solenoid valve 2 terminal A

* Cylinder deactivation solenoid valve 3 terminal B

* Cylinder deactivation solenoid valve 4 terminal D

瀚慖f the test lamp illuminates, test the control circuit for a short to ground. If the circuit tests normal, replace the ECM.

5. Remove the test lamp.

6. Command the appropriate cylinder deactivation solenoid ON with a scan tool. Verify the scan tool Cylinder Deactivation Solenoid Valve

Control Circuit High Voltage Test Status parameter displays OK.

瀚慖f not the specified value, test the appropriate control circuit listed below for a short to voltage. If the circuit tests normal, replace the

ECM.

* Cylinder deactivation solenoid valve 1 terminal C

* Cylinder deactivation solenoid valve 2 terminal A

* Cylinder deactivation solenoid valve 3 terminal B

* Cylinder deactivation solenoid valve 4 terminal D

7. Install a 3 A fused jumper wire between the appropriate control circuit terminal listed below and the ignition circuit terminal E. Command the

appropriate cylinder deactivation solenoid ON with a scan tool. Verify the scan tool Cylinder Deactivation Solenoid Valve Control Circuit

High Voltage Test Status parameter displays Malfunction.

* Cylinder deactivation solenoid valve 1 terminal C

* Cylinder deactivation solenoid valve 2 terminal A

* Cylinder deactivation solenoid valve 3 terminal B

* Cylinder deactivation solenoid valve 4 terminal D

瀚慖f not the specified value, test the control circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

8. If all the circuits test normal, test or replace the valve lifter oil manifold assembly.

Component Testing

Static Test

1. Ignition OFF, disconnect the harness connector at the valve lifter oil manifold assembly.

2. Connect the harness that is labeled resistance from the displacement on demand (DOD) tester to the valve lifter oil manifold connector.

3. Connect the power leads from the DOD tester to B+ and ground. Test for 11-18 ohm on each valve lifter oil manifold solenoid.

瀚慖f not within the specified range for each solenoid, replace the valve lifter oil manifold assembly.

4. Test for infinite resistance between each valve lifter oil manifold circuit terminal and the valve lifter oil manifold housing.

瀚慖f less than infinite resistance, replace the valve lifter oil manifold assembly.

Dynamic Test

1. Ignition OFF, disconnect the harness connector at the valve lifter oil manifold assembly.

2. Connect the cable that is labeled power from the displacement on demand DOD tester to the connector.

3. Connect the power leads from the DOD tester to B+ and ground.

4. Command each valve lifter oil manifold solenoid ON and OFF using the DOD tester. You should be able to hear each solenoid turn ON and

OFF.

瀚慖f the function does not perform as specified, replace the valve lifter oil manifold assembly.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Valve Lifter Oil Manifold Replacement (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and Push Rods/Lifter / Lash

Adjuster/Service and Repair/Valve Lifter Oil Manifold Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

All Other P Codes

If the P code is not listed, then:

No comments:

Post a Comment