Thursday, January 16, 2020

2010 Cadillac CTS Sedan AWD V6-3.6L Page 2047

2010 Cadillac CTS Sedan AWD V6-3.6L Page 2047



Component Connector End Views (See: Diagrams/Connector Views)



Description and Operation



Data Link Communications Description and Operation (See: Powertrain Management/Computers and Control Systems/Information



Bus/Description and Operation)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit



Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code



Descriptions/Control Module U Code List).



2. Verify that DTC U1814, U2099, B1428, B1370, B1380, B1440, or B1441 is not set.



瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code



Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).



3. Engine running for 10 seconds.



4. Ignition ON, engine OFF, verify that DTC U0100-U0299 is not set with symptom byte 00.



瀚慖f the DTC U0100-U0299 is set with symptom byte 00, refer to Circuit/System Testing.



5. Verify that DTC U0100-U0299 is not set with symptom byte 71 or 72.



瀚慖f the DTC U0100-U0299 is set with symptom byte 71 or 72 along with other DTCs set, diagnose all other codes first. Refer to



Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble Code (DTC) List -



Vehicle).



瀚慖f the DTC U0100-U0299 is set with symptom byte 71 or 72 and without other DTCs set, reprogram the control module. If the DTC



resets, replace the control module.



Circuit/System Testing



Note: Use the schematic to identify the following:



* Control modules the vehicle is equipped with



* Control module locations on the low and high speed GMLAN serial data circuits



* The control modules B+, ignition, ground, communication enable and serial data circuit terminals



1. Ignition OFF, disconnect the harness connector at of the control module that is not communicating.



2. Test for less than 10 ohm between each ground circuit terminal and ground.



瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.



3. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.



瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the



control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.



4. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.



瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test



the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.



Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wake up serial data circuit,



and the BCM is the output for these circuits. Refer to the control module schematics to identify which modules have these circuits.



5. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wake up



circuit terminal and ground.



瀚慖f the test lamp does not illuminate, test the entire circuit, including the B+ circuit to the BCM, for an open/high resistance or short to

No comments:

Post a Comment