Thursday, February 13, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 280

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 280



Conditions for Clearing the DTC



* This DTC will be current for as long as the fault is present



* When the fault is no longer present, the DTC will be a history DTC



* A history DTC will clear after 40 ignition cycles



Diagnostic Aids



DTC B1330 03 and B251A 02 may sent concurrently, correct the condition for setting DTC B1330 03 first before performing diagnostics testing



for B251A 02. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble Code



(DTC) List - Vehicle) to locate the correct procedure.



Reference Information



Schematic Reference



Door Lock/Indicator Schematics (See: Body and Frame/Locks/Diagrams/Electrical Diagrams/Door Lock/Indicator Schematics)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Description and Operation



Power Door Locks Description and Operation (See: Body and Frame/Locks/Power Locks/Description and Operation)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Ignition OFF, with the doors closed and locked, approach the vehicle with the keyless entry transmitter and pull the exterior driver door



handle. The driver door should unlock and unlatch allowing the driver door to be pulled open.



瀚慖f the driver door will not unlock and open with a single pull of the exterior door handle, refer to Driver Door Latch Malfunction.



2. With the doors closed and locked, approach the vehicle with the keyless entry transmitter and pull the exterior passenger door handle or the



exterior left rear door handle or the exterior right rear door handle. The appropriate door should unlock and unlatch allowing the door to be



pulled open.



瀚慖f all the passenger, left rear and right rear doors will not unlock and open with a single pull of the exterior door handle, refer to



Passenger and Rear Door Release Command Inoperative.



瀚慖f a door will not unlock and open with a single pull of the door handle, refer to Passenger or Rear Door Latch Malfunction.



Circuit/System Testing



Driver Door Latch Malfunction



1. Ignition OFF, disconnect the X2 harness connector at the K84 keyless entry control module.



2. Test for less than 10 ohm between the ground circuit terminal 6 and ground.



瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.



3. Ignition OFF, connect the X2 harness connector and disconnect the X4 harness connector at the K84 keyless entry control module.



4. Test for infinite resistance between the control circuit terminal 3 and ground.



瀚慖f less than the specified value, test the control circuit for a short to ground. If the circuit tests normal, replace the K9 BCM.



5. Ignition OFF, connect the X4 harness connector at the K84 keyless entry control module.



6. Disconnect the harness connector at the A23D door latch assembly - driver.



7. Connect a test lamp between the control circuit terminal 5 and control circuit terminal 10.



8. Pull and release the exterior driver door handle, the test lamp should briefly illuminate while the exterior door handle is being pulled.

No comments:

Post a Comment