Wednesday, February 12, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 979

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 979



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0010



- Intake Camshaft Position Actuator Solenoid Valve Control Circuit Bank 1



DTC P0013



- Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit Bank 1



DTC P0020



- Intake Camshaft Position Actuator Solenoid Valve Control Circuit Bank 2



DTC P0023



- Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit Bank 2



DTC P2088



- Intake Camshaft Position Actuator Solenoid Valve Control Circuit Low Voltage Bank 1



DTC P2089



- Intake Camshaft Position Actuator Solenoid Valve Control Circuit High Voltage Bank 1



DTC P2090



- Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit Low Voltage Bank 1



DTC P2091



- Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit High Voltage Bank 1



DTC P2092



- Intake Camshaft Position Actuator Solenoid Valve Control Circuit Low Voltage Bank 2



DTC P2093



- Intake Camshaft Position Actuator Solenoid Valve Control Circuit High Voltage Bank 2



DTC P2094



- Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit Low Voltage Bank 2



DTC P2095



- Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit High Voltage Bank 2



Circuit/System Description



The camshaft position actuator system enables the Engine Control Module (ECM) to change the timing of the camshafts while the engine is



operating. The Camshaft Position Actuator Solenoid Valve signal from the ECM is pulse width modulated (PWM). The ECM controls the



Camshaft Position Actuator Solenoid Valve duty cycle by controlling the amount of solenoid valve ON time. The Camshaft Position Actuator



Solenoid Valve controls the advance or the retard of each camshaft. The Camshaft Position Actuator Solenoid Valve controls the oil flow that



applies the pressure to advance or retard the camshafts.



Ignition voltage is supplied directly to the Camshaft Position Actuator Solenoid Valve. The ECM controls the solenoid valve by grounding the



control circuit with a solid state device called a driver. The driver is equipped with a feedback circuit that is pulled-up to a voltage. The ECM can



determine if the control circuit is open, shorted to ground, or shorted to a voltage by monitoring the feedback voltage.



Conditions for Running the DTC



* The engine speed is greater than 80 RPM.



* The ignition voltage is between 10-18 V.



* The ECM has commanded the Camshaft Position Actuator Solenoid Valve ON and OFF at least once during the ignition cycle.



* DTCs P0010, P0013, P0020, P0023, P2088, P2089, P2090, P2091, P2092, P2093, P2094, and P2095 run continuously once the above



conditions are met for greater than 1 second.



Conditions for Setting the DTC



P0010, P0013, P0020, P0023



The ECM detects an open in the Camshaft Position Actuator Solenoid Valve circuits for greater than 1 s or a cumulative of 5 s, when the solenoid



valve is commanded OFF.

No comments:

Post a Comment